Pop 123610 manual
Published on: Mar 4, 2016
Transcripts - Pop 123610 manual
Z-Wave Wall Plug Switch
Firmware Version : 1.0
A This is a Z-Wave actuator. Inclusion and Exclusion are confirmed by a tripple click of the button.
Please refer to the chapters below for detailed information about all aspects of the products usage.
What is Z-Wave?
This device is equipped with wireless communication complying to the Z-Wave standard. Z-Wave is the
international standard for wireless communication in smart homes and buildings. It is using the
frequency of 868.42 MHz to realize a very stable and secure communication. Each message is reconfirmed
(two-way communication) and every mains powered node can act as a repeater for other nodes (meshed
network) in case the receiver is not in direct wireless range of the transmitter.
Z-Wave differentiates between Controllers and Slaves. Slaves are either sensors (S) transmitting metered or
measured data or actuators (A) capable to execute an action. Controllers are either static mains powered
controllers (C) also referred to as gateways or mobile battery operated remote controls (R). This results in a
number of possible communication patterns within a Z-Wave network that are partly or completely supported
by a specific device.
1. Controllers control actuators
2. Actuators report change of status back to controller
3. Sensors report change of status of measured values to controller
4. Sensors directly control actuators
5. Actuators control other actuators
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 1
6. Remote controls send signals to static controllers to trigger scenes or other actions
7. Remote controls control other actuators.
There are two different role a controller can have. There is always one single primary controller that is managing the
network and including/excluding devices. The controller may have other functions - like control buttons - as well. All other
controllers don't manage the network itself but can control other devices. They are called secondary controllers. The
image also shows that its not possible to operate a sensor just from a remote control. Sensors only communicate with
This is a switch plug that can be placed between a standard Schuko (Type F) wall outlet and electric
devices, plugged in by cord. It can switch all electrical loads up to 3500 W. The device is IP 20 rated and
can therefore only be used on dry environments. Switching is controlled wirelessly using Z-Wave or locally
using a toggleing button. A blue LED indicates the switching status. An automatic 'Off' function and
programmable switching behavior make the device a very flexible tool for the inhouse lighting.
Before Device is installed
Please read carefully the enclosed user manual before installation of the radio-actuator, in order to ensure
an error-free functioning.
ATTENTION: only authorized technicians under consideration of the country-specific installation
guidelines/norms may do works with 230?Volt mains power. Prior to the assembly of the product, the
voltage network has to be switched off and ensured against re-switching.
The product is permitted only for proper use as specified in the user manual. Any kind of guarantee claim
has to be forfeited if changes, modifications or painting are undertaken. The product must be checked for
damages immediately after unpacking. In the case of damages, the product must not be operated in any
case. If a danger-free operation of the equipment cannot be assured, the voltage supply has to be
interrupted immediately and the equipment has to be protected from unintended operation.
The plug can be plugged into every wall outlet for Plug-Type Schuko. It is IP20 rated and can therefore only
be used in dry environments. Do not locate the device facing direct sunlight, humid or dusty place. The
suitable ambient temperature for the device is 0°C ~ 40°C. Plugs must not be stacked and operated.
Behavior within the Z-Wave network
I On factory default the device does not belong to any Z-Wave network. The device needs to join an
existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also leave a network. This process is called Exclusion. Both processes are initiated by the
primary controller of the Z-Wave network. This controller will be turned into exclusion respective inclusion
mode. Please refer to your primary controllers manual on how to turn your controller into inclusion or
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 2
exclusion mode. Only if the primary controller is in inclusion or exclusion mode, this device can join or leave
the network. Leaving the network - i.e. being excluded - sets the device back to factory default.
If the device already belongs to a network, follow the exclusion process before including it in your network.
Otherwise inclusion of this device will fail. If the controller being included was a primary controller, it has to
be reset first.
Inclusion and Exclusion are confirmed by a tripple click on the button.
Operating the device
The device is able to switch electric loads up to 3500 W and can be switched wirelessly or using the local
The local button allowes to switch the device. A short press on the button toggles the switch. If it is in on
state the button turns off and respective in off state the button turns on.
The device has one blue LED used to indicate status information. The behavior of the blue LED can be
It may show the switching state. This is the default option.
It may serve as night light. So it is on when the light is off.
It is deactivated.
It can be controlled wirelessly and used as an indicator for other advanced functions.
Automated Switch-Off Function
If activated the switch will turn off automatically after a defined time. This function is particularly useful if the
switch is turned on using a motion detector of any other type of sensor. In this case it is possible to further
define the reaction of the switch on certain signals sent from a sensor. This allowes a very flexible
application of the plug switch in the house.
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 3
The device can be turn into a child protection mode. In this mode all local operation is disabled.
The child protection mode MUST be turned on wirelessly. However in protected by sequence mode it is
possible to unlock the device for local operation with a triple click. The unlock state will last for 5 seconds.
A Z-Wave devices control other Z-Wave devices. The relationship between one device controlling
another device is called association. In order to control a different device, the controlling device needs to
maintain a list of devices that will receive controlling commands. These lists are called association groups
and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event
happens all devices stored in the respective association group will receive a common wireless command.
1 Send Reports on switch state change (max. nodes in group: 5)
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can
adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow to configure signed values. In order to set values in the range 128
… 255 the value sent in the application shall be the desired value minus 256. For example: to set a
parameter to 200? it may be needed to set a value of 200 minus 256 = minus 56. In case of two byte value
the same logic applies: Values greater than 32768 may needed to be given as negative values too.
LED mode (Parameter Number 1, Parameter Size 1) Set LED indication mode
1 Show switch state (Default)
2 Night mode (inverted switch state)
3 Operated by Indicator Command Class
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 4
Automatically switch off after (Parameter Number 2, Parameter Size 2) If not zero, automatically switch off
after a user defined time
0 Disabled (Default)
1 — 65535 sec
What to do on RF off command (Parameter Number 3, Parameter Size 1) Defines how to interpret RF Off
command. Can be used in conjunction with Auto Off function: Ignore - to switch on the light by motion
detectors and switch it off after some amount of time: in case of multiple motion detectors each would try to
switch the light off that would break logics; Switch on - to switch on the light on both On and Off paddle
press on the remote and switch it off after some amount of time. Button off click will still work (if button
operations are not disabled).
0 Switch off (Default)
2 Switch on
3 Switch on if load is off else switch off
Restore switch state after power cycle (Parameter Number 5, Parameter Size 1) Defines if the switch should
restore switch state to the last state prior to device power off (power cycle).
0 No, turn off
1 Yes (Default)
Supported Command Classes
Basic (version 1)
Binary Switch (version 1)
Version (version 1)
Indicator (version 1)
All Switch (version 1)
Configuration (version 1)
Manufacturer Specific (version 1)
Protection (version 1)
Node Naming and Location (version 1)
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 5
Association (version 2)
Power Supply 230V ~50-60 Hz
Attachable Loads all loads up to 3500 W
Type: T 1.25 A H (Load 1.25 Ampere, high shutdown capacity), D: 5 mm,
L: 20 mm
IP Rating 20
Frequency 868.42 MHz (SRD Band)
Wireless Range up to 100 m outside, on average up to 20 m inside buildings
Explorer Frame Support Yes
Device Type Slave with routing capabilities
Generic Device Class Binary Switch
Specific Device Class Binary Power Switch
Firmware Version 1.0
Explanation of Z-Wave specific terms
Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically
Gateways, Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators
and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one
primary controller in a Z-Wave network.
Inclusion — is the process of bringing new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to annonces that is is
able to communicate.
Node Information Frame — is a special wireless message issued by a Z_Wave device to announce its
capabilities and functions.
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 6
The product does not contain hazardous chemicals.
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and
get into the food chain, damaging your health and well-being.
(c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, All rights reserved, www.zwaveeurope.com - pp 7