of 5

# Pressure and kinetic energy of particles

Published on: Mar 4, 2016
Published in: Education

#### Transcripts - Pressure and kinetic energy of particles

• 1. Daniel Bernoulli, in 1738, was the first to understand airpressure from a molecular point of view. He drew a picture of a vertical cylinder, closed at thebottom, with a piston at the top, the piston having a weight on it, both piston and weight beingsupported by the air pressure inside the cylinder. He described what went on inside the cylinderas follows: “let the cavity contain very minute corpuscles, which are driven hither and thitherwith a very rapid motion; so that these corpuscles, when they strike against the piston and sustainit by their repeated impacts, form an elastic fluid which will expand of itself if the weight isremoved or diminished…”Movement of atom accordingThe Link between Molecular Energy and PressureIt is not difficult to extend Bernoulli’s picture to a quantitative description, relating the gaspressure to the molecular velocities. As a warm up exercise, let us consider a single perfectlyelastic particle, of mass m, bouncing rapidly back and forth at speed v inside a narrow cylinder oflength L with a piston at one end, so all motion is along the same line.Click here: DemonstrationWhat is the force on the piston?Obviously, the piston doesn’t feel a smooth continuous force, but a series of equally spacedimpacts. However, if the piston is much heavier than the particle, this will have the same effectas a smooth force over times long compared with the interval between impacts. So what is thevalue of the equivalent smooth force?
• 2. Using Newton’s law in the form force = rate of change of momentum, we see that the particle’smomentum changes by 2mv each time it hits the piston. The time between hits is 2L/v, so thefrequency of hits is v/2L per second. This means that if there were no balancing force, byconservation of momentum the particle would cause the momentum of the piston to change by2mv v/2L units in each second. This is the rate of change of momentum, and so must be equal tothe balancing force, which is therefore F = mv2/L.We now generalize to the case of many particles bouncing around inside a rectangular box, oflength L in the x-direction (which is along an edge of the box). The total force on the side ofarea A perpendicular to the x-direction is just a sum of single particle terms, the relevant velocitybeing the component of the velocity in the x-direction. The pressure is just the force per unitarea, P = F/A. Of course, we don’t know what the velocities of the particles are in an actual gas,but it turns out that we don’t need the details. If we sum N contributions, one from each particlein the box, each contribution proportional to vx2 for that particle, the sum just gives us N timesthe average value of vx2. That is to say,where there are N particles in a box of volume V. Next we note that the particles are equallylikely to be moving in any direction, so the average value of vx2 must be the same as thatof vy2 or vz2, and since v2 = vx2 + vy2 + vz2, it follows that
• 3. This is a surprisingly simple result! The macroscopic pressure of a gas relates directly to theaverage kinetic energy per molecule. Of course, in the above we have not thought about possiblecomplications caused by interactions between particles, but in fact for gases like air at roomtemperature these interactions are very small. Furthermore, it is well established experimentallythat most gases satisfy the Gas Law over a wide temperature range: PV = nRTfor n moles of gas, that is, n = N/NA, with NA Avogadro’s number and R the gas constant.Introducing Boltzmann’s constant k = R/NA, it is easy to check from our result for the pressureand the ideal gas law thatthe average molecular kinetic energy is proportional to the absolutetemperature,Boltzmann’s constant k = 1.38.10-23 joules/K.Newtons Laws and CollisionsApplying Newtons Laws to an ideal gas under the assumptions of kinetic theoryallows thedetermination of the average force on container walls. This treatment assumes that the collisionswith the walls are perfectly elastic.
• 4. In this development, an overbar indicates an average quantity. In the expression for the averageforce from N molecules, it is important to note that it is the average of the square of the velocitywhich is used, and that this is distinctly different from the square of the average velocity.Gas Pressure from Kinetic TheoryUnder the assumptions of kinetic theory, the average force on container walls has beendetermined to be and assuming random speeds in all directionsThe average force and pressure on a given walldepends only upon the components of Then the pressure in a container can bevelocity toward that wall. But it can be expressed in expressed asterms of the average of the entire translational kineticenergy using the assumption that the molecularmotion is random.Expressed in terms of average molecular kinetic energy: This leads to a concept of kinetic temperature and to theideal gas law. Kinetic TemperatureThe expression for gas pressure developed from kinetic theory relates pressure and volume to theaverage molecular kinetic energy. Comparison with the ideal gas law leads to an expressionfor temperature sometimes referred to as the kinetic temperature.
• 5. This leads to the expressionThe more familiar form expresses the average molecular kinetic energy:It is important to note that the average kinetic energy used here is limited to the translationalkinetic energy of the molecules. That is, they are treated as point masses and no account is madeof internal degrees of freedom such as molecular rotation and vibration. This distinction becomesquite important when you deal with subjects like the specific heats of gases. When you try toassess specific heat, you must account for all the energy possessed by the molecules, and thetemperature as ordinarily measured does not account for molecular rotation and vibration. Thekinetic temperature is the variable needed for subjects like heat transfer, because it is thetranslational kinetic energy which leads to energy transfer from a hot area (larger kinetictemperature, higher molecular speeds) to a cold area (lower molecular speeds) in directcollisional transfer.